aaaabbbbArcus 1200Owner's Guide! PrefaceThis chapter gives you general information about Arcus 1200.! Chapter 1: Preparing the ScannerThis chapte
Chapter 1: Preparing the Scanner 1021341 35 mm framed and 4 x 5 inch batch slide holder2 35 mm strip and 6 x 9 cm batch slide holder3 batch slide hol
Chapter 1: Preparing the Scanner 11Working with Trays and a Flexible TemplateTraysA locking system is installed for safety reasons, to protect the sc
Chapter 1: Preparing the Scanner 12Connecting the Transparency Unit (TPU)To scan negatives, transparencies or slides you have to use the TPU on your
Chapter 2: Installing the Scanner 13Chapter 2: Installing the ScannerThis chapter shows you how to set up your Arcus 1200 with your Apple Macintosh o
Chapter 2: Installing the Scanner 14Minimum Hardware and Software Requirements# For the Apple Macintosh:$ A Power Macintosh™$ 32 MB of RAM if virtua
Chapter 2: Installing the Scanner 15Environmental Requirements# Place the scanner on a horizontal, flat surface.# To ensure proper ventilation, all
Chapter 2: Installing the Scanner 16Cleaning Your Scanner# In order to maintain the quality of your scanned images, regularly clean the glass plate.
Chapter 2: Installing the Scanner 17Which SCSI Interface CardArcus 1200 requires a SCSI interface to work with your Macintosh. If your Macintosh does
Chapter 2: Installing the Scanner 18-or-If SCSI ID number 2 is already assigned, you need to set the scanner to a free SCSI IDnumber.$ Make sure that
Chapter 2: Installing the Scanner 19If your Arcus 1200 is the only external SCSI device to be connected to your AppleMacintosh:1 Place the terminator
Trademarks 2TrademarksAgfa, the Agfa rhombus and MultiPlate are trademarks of Agfa-Gevaert AG.Arcus 1200, FotoLook and ColorTune are trademarks of Agf
Chapter 2: Installing the Scanner 20If your Arcus 1200 will be connected to your Apple Macintosh together with other externalSCSI devices:If you inst
Chapter 2: Installing the Scanner 21If your scanner is the first external device of your SCSI chain1 Connect the 50-pin end of the SCSI cable to the
Chapter 2: Installing the Scanner 22If you install the scanner between two other external SCSI devices1 Disconnect the SCSI cable from one of these t
Chapter 2: Installing the Scanner 23Testing the Scanner and the ConnectionYou are now ready to check if the scanner is operating properly and if the
Chapter 2: Installing the Scanner 24Installation for WindowsThis section shows you how to set up your Arcus 1200 with your Windows PC. You can findin
Chapter 2: Installing the Scanner 25$ Make sure that your scanner is switched off and that it is disconnected from yourcomputer.$ To decrease the SCS
Chapter 2: Installing the Scanner 26If your PC has a 25-pin connector and your Arcus 1200 is the only external SCSI device tobe connected to your PC:
Chapter 2: Installing the Scanner 27If your PC has a 25-pin connector and your Arcus 1200 will be connected to your PCtogether with other external SC
Chapter 2: Installing the Scanner 28If your scanner is the first external device of your SCSI chain1 Set the scanner to an unused SCSI ID number betw
Chapter 2: Installing the Scanner 29If you install the scanner between two other external SCSI devices1 Set the scanner to an unused SCSI ID number b
Contents 3ContentsPreface ...
Chapter 2: Installing the Scanner 30If your PC has a 50-pin connector and your Arcus 1200 is the only external SCSI device tobe connected to your PC:
Chapter 2: Installing the Scanner 31If your PC has a 50-pin connector and your Arcus 1200 will be connected to your PCtogether with other external SC
Chapter 2: Installing the Scanner 32If your scanner is the first external device of your SCSI chain1 Set the scanner to an unused SCSI ID number betw
Chapter 2: Installing the Scanner 33If you install the scanner between two other external SCSI devices1 Set the scanner to an unused SCSI ID number b
Chapter 2: Installing the Scanner 34" Note: Make sure that you are using the correct power cord for the voltage in your area.Double-check wheth
Chapter 3: Placing Originals 35Chapter 3: Placing OriginalsThis chapter shows you how to scan with your Arcus 1200.! Changing Removable Trays! Placin
Chapter 3: Placing Originals 36Changing Removable TraysYour Arcus 1200 contains a removable glass plate as well as a removable batch slide holderfram
Chapter 3: Placing Originals 37" Note: Optical performance of a CCD scanner is always best near the middle of the scanarea. However, the specif
Chapter 3: Placing Originals 38Placing Transparent OriginalsWhen you scan transparent originals, there are two possibilities:# You can use the glass
Chapter 3: Placing Originals 392 Put the batch slide holder with the originals in the batch slide holder frame with the Agfa logoat the top.3 Insert
Contents 4Appendix A: Troubleshooting ... 41Append
Chapter 3: Placing Originals 4035 mm strip (1) and 6 x 9 cm (2) batch slide holderOne strip of maximum 6 negatives and 2 slides can be mounted into t
Appendix A: Troubleshooting 41Appendix A: TroubleshootingThis appendix explains some common problems you may come across when starting up or usingyou
Appendix A: Troubleshooting 42The scanner software cannot find the scanner.After opening the Scan dialog box, a message appears telling that no scann
Appendix B: Technical Information 43Appendix B: Technical InformationThis appendix provides some technical information about your Arcus 1200. Technic
Appendix B: Technical Information 44Lamp warm up time:Approximately 15 seconds180 seconds to reach final image qualityPower supply:100 V to 240 V, 47
Appendix C: Arcus 1200 Regulation Compliance 45Appendix C: Arcus 1200 RegulationCompliance! Safety Regulations! Electromagnetic Compatibility
Appendix C: Arcus 1200 Regulation Compliance 46Safety RegulationsArcus 1200 has been designed to comply with:# VDE 0805# IEC 950, EN 60950 (GS appr
Appendix C: Arcus 1200 Regulation Compliance 47Electromagnetic CompatibilityArcus 1200 is designed to comply with:# Emission: EN55022, Class B# Imm
Preface 5PrefaceArcus 1200 can scan reflective and transparent originals. Because of its MultiPlate™ system, it ispossible to prepare transparent ori
Chapter 1: Preparing the Scanner 6Chapter 1: Preparing the ScannerThis chapter assists you in preparing your Arcus 1200 for installation. You will fi
Chapter 1: Preparing the Scanner 7Unpacking the Scanner1 Open the packing box and take out all the items carefully.2 Check each item to make sure tha
Chapter 1: Preparing the Scanner 8 The TPU is unlocked.Taking a Closer LookNow that you have taken the scanner out of the box, you can take a closer
Chapter 1: Preparing the Scanner 9The Different Parts of Your ScannerThe figure illustrates the locations of the different parts of your Arcus 1200.2
Commentaires sur ces manuels